Engineering Plastics Suppliers & Grades

Machinable engineering plastics including PEEK, Delrin, Acetal, UHMW, Nylon 6/6, Cast Nylon, PTFE, PVDF, PPS, Polycarbonate, Ultem, and G-10/FR-4.

General metal service centers rarely carry machinable polymer rod or heavy sheet on their own floors. Production quantities of Acetal, Delrin, UHMW, Nylon, Ultem, and PEEK come from dedicated plastics distributors that saw-cut 48 x 96 in and 48 x 120 in sheets, 4 – 10 ft extruded rods, and cast nylon billets with resin lot traceability.

Engineering Plastics Grades & Trade Names

ABS

Sourcing guide

Acrylonitrile butadiene styrene. A common engineering thermoplastic with good impact resistance, machinability, and dimensional stability. The material 3D printers made famous, but in machining it's valued for its balanced properties and easy workability. Machines well at moderate speeds. Used for prototypes, enclosures, housings, and jigs. Compare to Polycarbonate (much higher impact resistance, transparent) and Acetal (stiffer, better wear resistance, more expensive).

Acetal (POM)

Sourcing guide

Acetal copolymer (POM-C). A crystalline engineering plastic with excellent dimensional stability, low moisture absorption, low friction, and good machinability. The most commonly machined engineering plastic alongside nylon. Machines beautifully at high speeds with sharp tools: clean chips, excellent surface finish, and tight tolerances achievable. Used for gears, bushings, bearings, valve components, and food processing equipment. Compare to Delrin (acetal homopolymer, slightly stronger and stiffer) and Nylon (absorbs moisture, slightly tougher).

Acetate

Sourcing guide

Cellulose acetate. A transparent thermoplastic derived from wood pulp. Used for display fixtures, eyeglass frames, and decorative applications where a warm, natural-looking transparency is desired. Machines well. Susceptible to moisture and some chemicals. Compare to Acrylic (better optical clarity, more brittle) and Polycarbonate (much tougher, less natural appearance).

Acrylic (Plexiglas)

Sourcing guide

PMMA (polymethyl methacrylate). Crystal-clear optical transparency (92% light transmission). Better clarity than polycarbonate but dramatically more brittle. It cracks and chips if you look at it wrong. Machines with care: use very sharp tools, moderate speeds, and avoid chatter or vibration. Drill slowly with peck cycles to avoid cracking. Used for displays, light guides, lenses, and decorative parts where optical clarity is the priority. Compare to Polycarbonate (tougher but less clear) and glass (harder but not machinable).

Cast Nylon 6

Sourcing guide

Cast Nylon 6. Produced by casting rather than extrusion, which allows much larger cross-sections (plates and rounds up to 30"+ diameter). Slightly lower strength than extruded Nylon 6/6 but available in sizes that extruded stock can't match. Lower moisture absorption than 6/6. Used for large gears, sheaves, wear plates, and structural components. Machines easily. Compare to Nylon 6/6 (slightly stronger, available in smaller sizes) and UHMW (lower friction but much softer).

CPVC

Sourcing guide

Chlorinated polyvinyl chloride. Higher-chlorine cousin of rigid Type 1 PVC that pushes continuous service temperature from 140°F up to 200°F while keeping strong resistance to hot acids, caustics, and plating-bath chemicals. Common in chemical manifolds, wet benches, and hot corrosive piping. Machines cleanly like PVC; keep cutters sharp and avoid overheating.

Delrin

Sourcing guide

DuPont's brand name for acetal homopolymer (POM-H). Slightly higher strength, stiffness, and hardness than acetal copolymer, with better creep resistance. The most recognized brand of acetal. Machines excellently. One of the most CNC-friendly plastics. Used for precision gears, cam followers, conveyor components, and any part requiring tight tolerances and dimensional stability. Compare to Acetal copolymer (slightly lower properties, better chemical resistance to hot water) and Nylon (tougher but absorbs moisture).

ECTFE

Sourcing guide

Ethylene chlorotrifluoroethylene (sold as Halar). Melt-processable fluoropolymer combining fluoropolymer chemical resistance (acids, solvents, strong oxidizers up to 300°F) with much better mechanical stiffness, abrasion resistance, and creep resistance than PTFE. Used for semiconductor wet-process manifolds, scrubber internals, and lined chemical valves.

ETFE

Sourcing guide

Ethylene tetrafluoroethylene (sold as Tefzel). Tough, high-impact fluoropolymer rated to ~300°F with strong radiation resistance, dielectric strength, and stiffer machining behavior than PTFE or FEP. Common in nuclear, aerospace wire standoffs, pump impellers, and chemical valve seats where PTFE cold-flows.

FEP

Sourcing guide

Fluorinated ethylene propylene. Optically clear, melt-processable cousin of PTFE rated to 400°F continuous service with near-universal chemical inertness and ultra-low friction. Primarily supplied as thin tubing, film, sight-glass liners, and encapsulation stock rather than heavy structural plate.

G-10/FR-4 (Garolite)

Sourcing guide

Glass-fiber reinforced epoxy laminate. Extremely strong and stiff for a plastic. FR-4 is the flame-retardant version used for printed circuit boards. G-10 is the base specification without flame retardancy requirements. Machines with carbide tooling because the glass fibers are abrasive and destroy HSS. Creates hazardous fiberglass dust; proper extraction and respiratory protection are mandatory. Used for electrical insulators, structural supports, circuit board substrates, and precision tooling. Compare to Phenolic Grade XX (cheaper, lower performance) and Carbon Fiber laminate (lighter, stiffer, more expensive).

GPO-3

Sourcing guide

Glass-polyester laminate. A thermoset laminate with good electrical insulation properties, arc resistance, and flame retardancy. Less expensive than G-10/FR-4. Used for electrical switchgear, bus bar supports, and transformer components. Machines with carbide due to glass fiber abrasiveness. Creates fiberglass dust, so use extraction. Compare to G-10/FR-4 (stronger, better mechanical properties) and Phenolic Grade XX (different base resin, similar applications).

HDPE

Sourcing guide

High-density polyethylene. Tough, chemically inert, FDA-approved for food contact, and inexpensive. Softer and more flexible than most engineering plastics. Used for cutting boards, tank liners, chemical containment, and food processing components. Machines easily but the softness can cause chatter on thin sections. Use sharp tools with high positive rake. Compare to UHMW (higher molecular weight, better wear resistance, similar applications) and Polypropylene (similar chemical resistance, slightly stiffer).

HIPS

Sourcing guide

High-impact polystyrene. Rubber-modified styrene sheet known for low cost, dead-easy routing and thermoforming, and clean matte paintability. Used for vacuum-formed trays, shop prototypes, templates, and display housings where structural load and solvent exposure are low. Compare to ABS (tougher and more chemical-resistant).

Kydex T

Sourcing guide

A thermoplastic acrylic-PVC alloy sheet. Known for its thermoformability. Heats easily and forms into complex shapes, then holds its shape when cooled. Used for knife sheaths, holsters, aircraft interior panels, medical device housings, and point-of-purchase displays. Machines with standard tooling. Excellent impact resistance and flame retardancy. Compare to ABS (similar applications, less flame retardant) and Polycarbonate (higher impact resistance, not as easily thermoformed into thin-gauge parts).

LDPE

Sourcing guide

Low-density polyethylene. Softer, more flexible, and more impact-compliant than HDPE, with broad acid/alkali inertness and FDA food-contact grades. Used for squeeze-fit seals, flexible corrosion shields, labware, and soft fixture pads. Clamps and deflects easily on the mill; use razor-sharp high-rake tools and vacuum or full-face backing.

Nylatron GS

Sourcing guide

Nylon with graphite and silicon additive for improved wear resistance and reduced friction. Self-lubricating. Used for bearings, bushings, and sliding components where maintenance-free operation is required. Machines similarly to standard Nylon. Compare to Nylatron GS (same material, brand name) and standard Nylon (higher friction, less wear-resistant).

Nylatron GSM

Sourcing guide

Nylatron GSM (graphite and MoS2-filled Nylon). Combines graphite and molybdenum disulfide fillers for maximum self-lubrication. The best bearing-grade nylon for dry running applications. Lower friction than either graphite-only or MoS2-only variants. Compare to Nylatron GS (graphite only) and Nylon MDS (MoS2 only).

Nylon 6

Sourcing guide

Extruded Polyamide 6 (PA6). Slightly tougher under impact and smoother in surface finish than Nylon 6/6, at a modest reduction in stiffness and melting point (~420°F vs 500°F) and slightly higher moisture uptake (~2.8~3.0% at saturation). Machines easily for wear pads, rollers, gears, and impact bumpers. For thick cross-sections above 3 – 4 inches, Cast Nylon 6 is usually more economical.

Nylon 6/6

Sourcing guide

Nylon 6/6 (polyamide). The most common engineering plastic for machined parts. Good strength, stiffness, and wear resistance. Excellent for gears, bushings, wear pads, and food processing components. Machines easily with standard tooling at high speeds. Absorbs moisture, which causes dimensional growth (up to 2.5%), so account for this in precision work. Compare to Delrin/Acetal (better dimensional stability, less moisture absorption) and UHMW (better impact resistance, lower friction, but softer).

Nylon MDS

Sourcing guide

Nylon with molybdenum disulfide (MoS2) additive. The MoS2 provides self-lubrication and improved wear resistance. Used for gears, bearings, and wear components in dry-running applications. Black or dark gray color (from the MoS2). Machines like standard Nylon. Compare to Nylon GS (graphite-filled, similar concept) and standard Nylon (no lubricant filler).

PBT

Sourcing guide

Polybutylene terephthalate (often sold as Hydex or Celanex). Semi-crystalline thermoplastic polyester with very low moisture absorption (~0.1%), strong electrical insulation even in humid washdown environments, and good chlorine/caustic cleaning resistance. Used for food-equipment pistons, sensor housings, and electrical bobbins. Compare to PET/Ertalyte (stiffer, higher wear) and Acetal (easier to source).

PCTFE

Sourcing guide

Polychlorotrifluoroethylene (historically Kel-F 81). The premier cryogenic fluoropolymer: near-zero moisture absorption, zero cold-flow compared to PTFE, low gas permeability, and reliable sealing from -400°F liquid oxygen/nitrogen/LNG service up to +300°F. Very expensive per pound; machine stress-relieved rod carefully with sharp carbide and avoid overheating.

PEEK

Sourcing guide

Polyether ether ketone. The premium engineering plastic. Exceptional strength, stiffness, and temperature resistance (continuous use to 480°F). Chemical resistance rivals fluoropolymers. Machines beautifully with standard tooling at moderate speeds. The catch: it costs $50-100+ per pound. Used for aerospace components, medical implants, semiconductor equipment, and oil and gas downhole tools where nothing else can handle the environment. Compare to Ultem 1000 (similar temperature resistance, much cheaper) and Torlon 4301 (higher temperature capability).

PET

Sourcing guide

Polyethylene terephthalate (machining grade sold as Ertalyte or Sustadur PET). Semi-crystalline polyester that holds tighter tolerances in wet environments than Nylon and wears longer under high bearing loads than Acetal. Nearly zero moisture swell, stain-resistant, and widely available in FDA-compliant white and black rod and plate for food filling pistons, manifold blocks, and precision slides. Slightly more notch-sensitive than Delrin; leave generous corner radii.

PETG

Sourcing guide

Glycol-modified polyethylene terephthalate (Vivak / Spectar). Clear amorphous sheet plastic sitting between Acrylic and Polycarbonate in price and toughness: far more impact-resistant than Acrylic, easier to bend, die-cut, and thermoform without pre-drying than Polycarbonate, and FDA-compliant for medical packaging trays, machine guards, and sterile housings.

PFA

Sourcing guide

Perfluoroalkoxy alkane. Ultra-high-purity melt-processable fluoropolymer matching PTFE's 500°F continuous temperature rating and universal chemical resistance, with smoother non-porous surfaces (minimizing ionic extractables) and higher creep resistance. Standard in semiconductor wafer wet benches, ultra-pure acid valves, and pharmaceutical fluid handling.

Phenolic Canvas

Sourcing guide

Canvas-reinforced phenolic laminate (LE grade). Cotton canvas impregnated with phenolic resin. Good impact resistance and machinability. Used for gears, bearings, washers, and structural supports where the fabric reinforcement provides toughness that paper-based phenolic lacks. Machines with standard HSS or carbide. Compare to Phenolic Linen (similar but with finer linen fabric) and G-10/FR-4 (glass-reinforced, much stronger).

Phenolic Canvas Electric

Sourcing guide

Canvas-reinforced phenolic laminate with electrical-grade properties. Good dielectric strength for moderate voltage applications. Used for electrical switchgear components, panel boards, and insulators. Compare to Phenolic Canvas (mechanical grade) and G-10/FR-4 (better electrical properties, more expensive).

Phenolic Grade XX

Sourcing guide

Paper-reinforced phenolic laminate (Grade XX). Paper layers impregnated with phenolic resin. Good machinability and electrical insulation. The most common phenolic grade for general-purpose machined electrical components. Used for terminal boards, insulators, and structural electrical parts. Machines cleanly with standard tooling. Compare to Phenolic Canvas (better impact resistance) and G-10/FR-4 (much stronger, better electrical properties).

Phenolic Linen

Sourcing guide

Linen-reinforced phenolic laminate (LE grade). Fine linen fabric layers give better machinability and surface finish than canvas grades. Used for gears, bearings, and precision electrical components. The best-machining phenolic grade. Compare to Phenolic Canvas (tougher, coarser) and Phenolic Grade XX (paper-based, less impact resistant).

Phenolic Linen Electric

Sourcing guide

Linen-reinforced phenolic laminate with electrical-grade properties. Combines the machinability of linen phenolic with dielectric requirements. Used for precision electrical components. Compare to Phenolic Linen (mechanical grade) and G-10/FR-4 (better electrical properties).

Polycarbonate (Lexan)

Sourcing guide

A transparent engineering thermoplastic with exceptional impact resistance, essentially unbreakable in normal use. Optically clear. Used for machine guards, sight glasses, protective shields, and transparent enclosures. Machines well with sharp tools at moderate speeds. Use coolant to avoid surface hazing from heat. Don't use ammonia-based coolants. Polycarbonate is sensitive to stress cracking from certain chemicals. Compare to Acrylic (optically clearer but brittle) and PETG (cheaper, good clarity, less impact resistant).

Polyester

Sourcing guide

Polyester thermoplastic (PET or PBT). Good mechanical properties, dimensional stability, and chemical resistance. Used for electrical connectors, structural components, and food processing equipment. Machines well with standard tooling. Compare to Acetal (better wear resistance) and Nylon (tougher but absorbs moisture).

Polypropylene

Sourcing guide

A semi-crystalline thermoplastic with excellent chemical resistance, low density, and good fatigue resistance (living hinges). Cheaper than most engineering plastics. Machines adequately but the low stiffness can cause chattering and deflection. Use sharp tools with high positive rake and support thin sections well. Used for chemical tanks, acid-resistant cabinets, and lab equipment. Compare to HDPE (similar chemical resistance, tougher) and Nylon (much stronger and stiffer).

PPO

Sourcing guide

Modified polyphenylene oxide / PPE-PS blend (sold as Noryl). Amorphous engineering plastic prized for hydrolytic stability (virtually zero water absorption at 0.06%), tight dimensional control, UL 94 V-0/V-1 flame ratings, and reliable dielectric properties. Common in water-meter internals, pump housings, telecom brackets, and electrical enclosures.

PPS

Sourcing guide

Polyphenylene sulfide (sold as Techtron PPS or Ryton). High-temperature crystalline polymer rated to 425°F continuous service with zero known solvents below 390°F, near-zero moisture absorption, and rock-solid dimensional stability. Bridges the price gap between Acetal/Ultem and PEEK for chemical pump housings, analytical manifolds, downhole rings, and steam-washdown bushings. Unfilled bearing grades machine crisply; glass-filled PPS (40% GF) requires carbide or PCD tooling.

PPSU

Sourcing guide

Polyphenylsulfone (sold as Radel R). Amorphous sulfone polymer built for repeated steam autoclaving (1,000+ cycles without crazing) and high notched-impact toughness. Standard for reusable orthopedic surgical trials, sterilization trays, and hot-water aircraft manifolds, typically carried in bone-white, black, and medical colors.

PSU

Sourcing guide

Polysulfone (sold as Udel). Rigid, amber-transparent amorphous thermoplastic rated to 300°F continuous service with strong resistance to hot water, steam, mineral acids, and dairy/food sanitizers. Used for sight glasses, analytical fluid manifolds, membrane housings, and medical manifolds where Polycarbonate stress-cracks. Anneal after heavy machining to prevent solvent crazing.

PTFE (Teflon)

Sourcing guide

Polytetrafluoroethylene (Teflon). The lowest friction of any solid material and chemically inert to virtually everything. Soft (Shore D 50-55), which means it deforms under load and requires creative workholding. Machines easily but the material is slippery and doesn't clamp well, so use vacuum fixtures or wrap it. Used for seals, gaskets, bearings, insulators, and chemical-resistant linings. Compare to UHMW (much tougher, slightly higher friction) and PEEK (much stronger, similar chemical resistance, much more expensive).

PVC

Sourcing guide

Polyvinyl chloride, rigid (Type 1). Good chemical resistance, flame retardancy, and mechanical properties at low cost. Used for chemical processing tanks, valve bodies, fume hoods, and electrical enclosures. Machines well with sharp tools at moderate speeds. Do NOT overheat. PVC generates toxic hydrochloric acid fumes when it gets too hot. Use coolant and keep speeds moderate. Compare to CPVC (higher temperature rating) and Polypropylene (lighter, better chemical resistance in some environments).

PVDF (Kynar)

Sourcing guide

Polyvinylidene fluoride (sold as Kynar or Symalit). High-purity, rigid crystalline fluoropolymer rated to 300°F that machines and welds like a true structural plastic without PTFE's softness or creep. Resistant to halogens, strong acids, bromines, and UV exposure, making it the default plastic for semiconductor ultrapure water systems, chemical tank nozzles, plating racks, and valve bodies.

Torlon 4301 (PAI)

Sourcing guide

Polyamide-imide (PAI). The highest-performing unfilled thermoplastic you can machine. Continuous use to 500°F with strength retention that embarrasses most plastics at room temperature. Used for jet engine components, semiconductor equipment, and anywhere you'd use metal but need the weight savings or chemical resistance of plastic. Very expensive ($100+ per pound). Machines with carbide at moderate speeds. Compare to PEEK (similar temperature range, less strong, cheaper) and Vespel (polyimide, even higher temperature but essentially unmoldable, machined only).

UHMW

Sourcing guide

Ultra-high molecular weight polyethylene. The impact-resistant, self-lubricating, noise-dampening workhorse of industrial plastics. Extremely low coefficient of friction, excellent abrasion resistance, and virtually unbreakable under impact. FDA-approved. Used for conveyor guides, chute liners, wear strips, dock fenders, and food processing equipment. Machines easily but can be grabby, so use sharp tools, moderate speeds, and make sure the material is well-supported. The softness (Shore D 62-66) means it deflects under clamping pressure, so don't over-tighten. Compare to HDPE (cheaper, less wear-resistant) and Nylon (stronger and stiffer but absorbs moisture).

Ultem 1000 (PEI)

Sourcing guide

Polyetherimide (PEI). A high-temperature amorphous thermoplastic with continuous use to 340°F. Transparent amber color. Excellent strength, stiffness, and dimensional stability. Inherently flame-retardant with low smoke generation. Machines well with standard tooling. Used for aerospace interior panels, medical devices, electrical connectors, and food service equipment. Much cheaper than PEEK or Torlon 4301. Compare to PEEK (higher temperature, much more expensive) and Polycarbonate (lower temperature, better transparency, cheaper).

Ultem 2300

Sourcing guide

Glass-fiber reinforced Ultem (PEI with 30% glass fiber). Dramatically higher strength and stiffness than unfilled Ultem 1000, with better dimensional stability and heat deflection temperature. Machines with carbide due to glass fiber abrasiveness. Used for structural aerospace components, electronic housings, and high-performance connectors. Compare to Ultem 1000 (unreinforced, easier to machine) and PEEK GF30 (glass-filled PEEK, higher temperature capability).

US Suppliers That List Engineering Plastics

Showing 5 of 48 suppliers in our directory. Filter by grade, shape, and ship-to state in Supplier Search.

Filter by state (48 total)

How Shop Buyers Choose an Engineering Plastic

Quick side-by-side reference for common forms, shop applications, and purchasing pitfalls before you send out quotes.

GradeTypical Forms & SizesBest Shop FitWhat to Watch Out For
Acetal / DelrinRod (4 – 8 ft), sheet & plate (24 x 48 in, 48 x 96 in)Tight-tolerance CNC gears, manifolds, fixtures, and wet washdown partsHomopolymer (Delrin 150) can show centerline porosity in rod over 2.5 in; copolymer avoids it
UHMWSheet & wear plate (48 x 96 in, 48 x 120 in), rod, milled profilesConveyor guide rails, chute liners, dock bumpers, and high-impact wear stripsSoft (Shore D 62 – 66) and high thermal expansion; bows if clamped hard or milled on one face only
Nylon 6/6 & Cast Nylon 6Extruded rod/plate under 3 in; cast rod, tube & plate up to 30+ inHeavy sheaves, crane pads, bushings, rollers, and dry-running wear padsAbsorbs up to 2.5% moisture in humid air, growing dimensionally after machining
PET (Ertalyte)Rod (4 – 8 ft) and heavy plate in natural white and blackFDA food-filling pistons, precision slides, and high-load wear parts in wet serviceMore notch-sensitive than Acetal; avoid sharp internal corners and impact shock
G-10/FR-4Sheet & plate (36 x 48 in, 48 x 96 in), rod, molded tubeStructural electrical standoffs, test fixtures, bus-bar supports, and cryogenic spacersAbrasive glass cloth ruins HSS cutters fast and generates fiberglass dust; run carbide and extraction
Ultem 1000 (PEI) & PEEKStress-relieved rod, heavy gauge plate, and tubular bar340 – 480°F continuous heat, downhole seals, autoclave trays, and semiconductor manifoldsHigh per-pound cost ($40 – $120+/lb); confirm unfilled vs 30% glass-filled or bearing grade on the print

What to Specify on an Engineering Plastics RFQ

Include these details on line 1 of your quote request so distributors price the same spec and surface finish.

Virgin vs reprocessed resin and exact color

UHMW, HDPE, and PTFE are sold in both virgin and reprocessed (regrind) grades. Virgin natural is usually required for FDA 21 CFR, USDA, or semiconductor purity, while black or green reprocessed sheet cuts liner costs by 15~30%.

Homopolymer vs copolymer and brand allowances

Prints that say 'Delrin or equivalent' allow Acetal copolymer (POM-C), which costs less and avoids centerline porosity in larger diameters. Prints calling out DuPont Delrin 150 or ASTM D4181 POM0111 require true homopolymer.

Extruded vs cast and stress-relieved condition

Above 3 in thickness or 4 in diameter, Cast Nylon 6 and compression-molded PEEK/PTFE are far cheaper and less stressed than extruded shapes. Specify annealed/stress-relieved stock when hogging deep pockets in Ultem, PSU, or PEEK.

Compliance paperwork with the quote

Ask up front for Resin Lot Traceability, FDA food-contact letters, USP Class VI biocompatibility, UL 94 V-0 flame certs, or AMS/MIL resin certs; plastics distributors cannot recreate lot certs after cutting unmarked offcuts.

Frequently Asked Questions: Buying Engineering Plastics

Why don't metal service centers carry engineering plastics?
Plastics are produced by polymer extruders, compression molders, and laminators (such as Ensinger, Roechling, Drake, and Mitsubishi Chemical) and distributed through dedicated plastics houses. Quoting a plastics distributor directly avoids the broker markup a metal house adds when buying polymer blanks outside its own warehouse.
When should a shop request Acetal copolymer instead of Delrin?
Delrin is an acetal homopolymer with ~10~15% higher tensile stiffness, while Acetal copolymer resists hot water, caustic washdown, and centerline porosity in diameters above 2.5 inches. Unless the print locks in ASTM homopolymer or a DuPont brand callout, asking the customer to approve copolymer often lowers bar cost and scrap risk.
What are standard sheet and rod sizes for machinable plastics?
Commodity sheets (UHMW, HDPE, Polycarbonate, Acrylic, PVC, ABS) typically come in 48 x 96 in and 48 x 120 in sheets. High-performance plates (PEEK, Ultem, Torlon, PPS, PVDF) are commonly molded or extruded in 24 x 48 in or metric 610 x 1220 mm slabs, and rods in 4 ft, 8 ft, or 10 ft lengths with oversized +0.020 – +0.125 in machining allowance.