Tool Steel Suppliers & Grades
Cold-work, hot-work, plastic-mold, shock-resistant, and high-speed tool steels including A2, D2, O1, H13, S7, P20, M2, M4, and W1 in annealed rounds, flats, drill rod, and precision ground flat stock.
Buying tool steel well comes down to choosing the right mill finish before the block hits your vise. Ordering DeCarb-Free (DCF) flats or Precision Ground Flat Stock (PGFS) instead of hot-rolled black bar often saves more spindle time than the raw material price difference.
Tool Steel Grades & Trade Names
A2
Live pricesAir-hardening tool steel. The general-purpose die steel. Hardens uniformly by cooling in still air after austenitizing, which minimizes distortion compared to oil- or water-hardening grades. Reaches HRC 57-62 with good toughness and wear resistance. Machine annealed (HRC ~25), then heat treat. In the annealed state it machines reasonably well with carbide. After hardening, it's grinding and EDM only. Used for blanking dies, forming dies, punches, and gauges. Compare to D2 (higher wear resistance, more chromium) and O1 (oil-hardening, cheaper, more distortion during heat treat).
A6
Sourcing guideAir-hardening tool steel similar to A2 but with manganese instead of some chromium. Lower austenitizing temperature (1525°F vs 1750°F for A2) means less scaling and less thermal shock during heat treatment. Good combination of wear resistance and toughness at HRC 58-62. Slightly less wear-resistant than A2 but easier to heat treat with less distortion. Used for gauges, mandrels, shear blades, and precision tools where dimensional stability during heat treatment is critical. Compare to A2 (more common, slightly better wear resistance) and O1 (oil-hardening, cheaper, simpler heat treat but more distortion).
CPM 20CV
Live pricesA Crucible particle metallurgy (CPM) stainless tool steel with 1.9% carbon, 20% chromium, 4% vanadium, and 1% molybdenum. Truly stainless with extreme wear resistance from massive vanadium carbide content. PM (powder metallurgy) process ensures fine, uniform carbide distribution impossible to achieve through conventional melting. HRC 59-61. Used for high-performance knife blades, plastic injection molding screws and barrels where both corrosion resistance and abrasion resistance are needed. Compare to D2 (much cheaper, semi-stainless, less wear-resistant) and CPM S30V (less wear-resistant but tougher).
D2
Live pricesHigh-carbon, high-chromium cold work tool steel (1.5% C, 12% Cr). Semi-stainless. The chromium gives it better corrosion resistance than A2 or O1, though it's not truly stainless. Excellent wear resistance at HRC 58-62. Air-hardens with minimal distortion. The go-to steel for high-volume stamping dies, slitting knives, and forming tools where edge life matters most. Machines in the annealed condition with carbide. After hardening, it's grinding, EDM, or hard machining with CBN. Also popular for knife blades. Compare to A2 (tougher, less wear-resistant) and M2 (HSS, better hot hardness for cutting tools) and 440C stainless (true stainless, similar hardness but less wear-resistant).
H13
Live pricesHot work tool steel (5% chromium, 1.35% molybdenum, 1% vanadium). The standard for die-casting dies, extrusion tooling, and hot forging dies. Maintains hardness and toughness at elevated temperatures (up to 1000°F+). Typically used at HRC 44-52. Machines well in the annealed condition with carbide. In the pre-hardened condition, use coated carbide at reduced speeds. Used for aluminum die-casting dies, extrusion mandrels, hot shear blades, and forging dies. Compare to S7 (better impact resistance, lower hot hardness) and A2 (cold work, not for elevated temperatures).
L6
Sourcing guideNickel-bearing oil-hardening cold-work tool steel (~0.70% C, 1.5% Ni, 0.75% Cr). Nickel gives L6 unusual shock toughness and deep through-hardening among oil-hardening steels at HRC 54 – 60. Used for band and circular saw blades, heavy punches, clutches, and machine-tool spindles. Compare to O1 (less tough, higher wear) and S7 (higher shock resistance).
M2
Live pricesHigh-speed steel (HSS). The standard material for cutting tools: drill bits, end mills, taps, and broaches. 6% tungsten, 5% molybdenum, 2% vanadium give it excellent hot hardness (retains cutting ability at the high temperatures generated during metal cutting). HRC 60-65. Not typically machined in the shop. You buy it as finished tools or as blanks to grind. If you do machine M2 in the annealed condition, it cuts like a tough alloy steel. Compare to M42 cobalt HSS (even better hot hardness) and carbide (much harder and faster but more brittle).
M4
Sourcing guideHigh-vanadium molybdenum high-speed tool steel (~1.35% C, 4% V, 5.5% W, 4.5% Mo). Roughly double the vanadium carbide volume of M2 gives M4 exceptional abrasive wear resistance at HRC 62 – 65 for cold-extrusion punches, fine-blanking dies, broaches, and form tools. Commonly ordered in powder-metallurgy form (CPM M4) to prevent carbide segregation and improve grindability.
O1
Live pricesOil-hardening tool steel. The simplest and most forgiving tool steel to heat treat. Austenitize at 1450°F, quench in oil, temper. Reaches HRC 57-62. Lower cost than A2 or D2. The tradeoff is more distortion during heat treatment compared to air-hardening grades. Machines well annealed. Used for jigs, fixtures, gauges, blanking dies, and hand tools. Popular with hobbyists and bladesmiths because of the straightforward heat treatment. Compare to A2 (less distortion, more expensive) and W1 (water-hardening, even cheaper but even more distortion).
O2
Sourcing guideManganese oil-hardening cold-work tool steel (~0.90% C, 1.6% Mn; DIN 1.2842 equivalent). Very close to AISI O1 in shop handling, machinability, and dimensional stability during oil quench to HRC 58 – 62, without O1's small tungsten/chromium additions. Common on European-designed tooling prints for gauges, guide rails, and blanking dies.
O6
Sourcing guideGraphitic oil-hardening tool steel (~1.45% C, 1.0% Si, 0.25% Mo). Roughly a third of its carbon precipitates as free microscopic graphite pockets, giving annealed O6 easy, clean machining and giving hardened parts (HRC 58 – 63) built-in dry lubricity and anti-galling resistance for draw dies, bushings, mandrels, and slide ways.
P20
Sourcing guidePre-hardened chromium-molybdenum plastic mold steel supplied ready to machine at ~HRC 28 – 32 (300 BHN). Because cavities are finish-milled and polished directly in the pre-hardened block without post-machining heat-treat distortion, P20 is the default steel for thermoplastics injection molds, die-casting bolster plates, and heavy shop fixtures. Polishes cleanly and accepts texturing or nitriding.
S1
Sourcing guideTungsten-chromium shock-resistant tool steel (~0.50% C, 2.2% W, 1.4% Cr). Oil-hardens to HRC 52 – 58 with strong resistance to repeated impact and moderate heat checking. Used for pneumatic chisels, rivet sets, heavy shear blades, and hot/cold swaging dies. Compare to S7 (air-hardening, simpler heat treat and wider US availability).
S5
Sourcing guideSilicon-manganese shock-resistant tool steel (~0.55% C, 2.0% Si, 0.8% Mn, 0.4% Mo). Oil-hardens to HRC 55 – 60 with higher elastic limit and wear resistance than S7 on concrete breaker bits, shear blades, nail dies, and heavy-impact punches, though it is more prone to decarburization and quench distortion than air-hardening S7.
S7
Live pricesShock-resistant tool steel. The highest impact toughness of any common tool steel. Designed for tools that take repeated heavy blows: chisels, punches, shear blades, and forming dies on heavy presses. Air-hardens to HRC 56-58 with exceptional resistance to chipping and cracking. Also has decent hot hardness, making it useful for some hot-work applications. Machines well annealed. Compare to H13 (better hot hardness, less impact resistance) and A2 (better wear resistance, less toughness).
W1
Live pricesWater-hardening tool steel. The simplest and cheapest tool steel. Essentially high-carbon steel (0.70-1.50% C) with the specification controls expected of tool steel. Hardens by water quench to HRC 64-66 on the surface. Only shallow-hardens, so the core stays soft and tough. Maximum distortion during heat treatment among common tool steels. Used for cold heading dies, woodworking tools, hand tools, and springs. Popular with bladesmiths for its fine grain and excellent edge quality. Compare to O1 (oil-hardening, less distortion, slightly more expensive) and 1095 (similar carbon content, basic carbon steel without tool steel controls).
US Suppliers That List Tool Steel
Showing 5 of 9 suppliers in our directory. Filter by grade, shape, and ship-to state in Supplier Search.
How Shop Buyers Choose a Tool Steel Grade
Quick side-by-side reference for common forms, shop applications, and purchasing pitfalls before you send out quotes.
| Grade | Typical Forms & Sizes | Best Shop Fit | What to Watch Out For |
|---|---|---|---|
| O1 (Oil-Hardening) | 36 in drill rod, 18 in & 36 in PGFS, DCF flats | Shop gauges, drill bushings, locating pins, jigs, and short-run blanking dies | Moves more during oil quench than air-hardening A2; avoid on thin, complex wire-EDM frames |
| A2 (Air-Hardening) | DCF flats & squares, rounds, PGFS, and 36 in drill rod | General-purpose stamping punches, forming dies, slitter spacers, and precision gauges | Balanced wear and toughness (HRC 57 – 62), but step up to D2 on abrasive fiberglass or stainless stamping |
| D2 (High-Carbon High-Chrome) | DCF flats, rounds, rings, and PGFS | Long-run blanking/trimming dies, shear blades, thread-rolling dies, and pelletizer knives | Coarse carbides reduce impact toughness and slow surface grinding; consider CPM M4 or S7 if edges chip |
| S7 (Shock-Resistant) | DCF flats, rounds, drill rod, and plate | Heavy impact punches, cold-heading dies, chisels, swaging blocks, and jaw inserts | Tops out around HRC 56 – 58; wears faster than A2/D2 in pure sliding abrasion |
| H13 (Hot-Work) | ESR/premium annealed rounds, forged blocks, and DCF flats | Aluminum die-casting dies, extrusion mandrels, hot-forging inserts, and hot shear knives | Die-casting cavities require NADCA #229 / ESR premium micro-cleanliness to prevent thermal-fatigue cracking |
| P20 (Pre-Hardened Mold) | Pre-hardened saw-cut blocks and plate (HRC ~28 – 32) | Thermoplastic injection mold bases/cavities, blow molds, and zero-heat-treat shop fixtures | Supplied pre-hardened; verify standard P20 vs higher-hardness P20+Ni (HH) on large mold blocks |
What to Specify on a Tool Steel RFQ
Include these details on line 1 of your quote request so distributors price the same spec and surface finish.
Surface finish: Hot-Rolled vs DeCarb-Free (DCF) vs Precision Ground (PGFS)
Hot-rolled tool steel carries mill scale and decarburized bark that must be milled off all six faces so the part hardens evenly. DCF/econ-o-miser stock arrives milled oversize (+0.015 – +0.035 in) free of decarb, and PGFS arrives ground within ±0.001 in.
Drill rod water/oil/air code
Tool-room drill rod in 36 in (and 12 ft) lengths uses traditional names too: 'Watercrat' (W1), 'Oilcrat' (O1), 'Aircrat' (A2), and 'Commercial/Silver Steel'. Always call out the AISI grade (W1, O1, A2, D2, S7, M2) alongside diameter tolerance.
Annealed vs pre-hardened condition and melt cleanliness
A2, D2, O1, and S7 normally ship spheroidized-annealed (~200 – 245 BHN) for machining prior to heat treat, whereas P20 ships pre-hardened (~300 BHN) and H13 is sold both annealed and pre-hardened. Specify ESR/NADCA quality when quoting die-cast cavities.
Grain direction on saw-cut die blocks
When buying custom saw-cut A2, D2, or S7 blocks from master plate, tell the distributor which dimension is rolling-grain length so long punches or shear blades don't end up cut transverse to the grain.
Frequently Asked Questions: Buying Tool Steel
- What is the difference between DeCarb-Free (DCF) flat bar and Precision Ground Flat Stock (PGFS)?
- DCF (often called ' Deluxe' or 'Econ-O-Miser') is milled on thickness and width to +0.015 – +0.035 in oversize so all decarburized mill bark is gone and you have cleanup stock after heat treat. PGFS is surface-ground to nominal thickness (±0.001 in) in standard 18 in or 36 in lengths for gauges and parts finished directly to print.
- Should a shop choose A2 or D2 for stamping and forming tooling?
- Use A2 for general runs under ~100,000 hits, thicker stock, or punches with small features that need chipping resistance and easy grinding. Step up to D2 when stamping abrasive strip (stainless, silicon steel, fiberglass laminates) or high-volume runs where edge wear dictates tool pulls.
- Why do die-casting shops specify ESR H13 instead of commercial H13?
- Electro-Slag Remelted (ESR) H13 removes non-metallic inclusions and refines ingot segregation, preventing premature heat-checking and gross cracking when molten aluminum thermally shocks the die face thousands of times.
Already have a supplier quote in hand? Check if the price is fair.