Stainless Steel Suppliers & Grades
Austenitic, martensitic, duplex, and precipitation-hardening stainless steels including 303, 304/304L, 316/316L, 416, 440C, 2205, 2507, Nitronic 50/60, and 17-4 PH.
Stainless steel quotes move monthly with mill alloy and fuel surcharges (driven by nickel, chromium, and molybdenum) and split sharply by product form: flat-rolled coil/sheet processors dominate 304/316 laser blanks, while bar depots lead on pump-shaft quality, Swiss-ground 303/17-4, and duplex grades.
Stainless Steel Grades & Trade Names
15-5 PH
Live prices15-5 PH (precipitation-hardening martensitic stainless). Essentially a vacuum-melted, wrought version of 17-4 PH chemistry with improved transverse mechanical properties and better fracture toughness. Machines similarly to 17-4. In Condition A it's reasonable; after aging to H900 it gets quite hard. Used for aerospace structural parts, nuclear components, and applications requiring more reliable transverse strength than 17-4. Slightly more expensive. Compare to 17-4 PH (more common, adequate for many applications) and 13-8 Mo (even higher strength).
17-4 PH
Live pricesA precipitation-hardening martensitic stainless. In Condition A (annealed) it machines similarly to 304, but once aged to H900 it gets significantly harder and tougher on tools. Most shops machine it in Condition A then send it out for heat treat. It shrinks predictably during aging (roughly 0.0005 in/in), so leave allowance. Responds well to high-efficiency trochoidal toolpaths with low radial engagement and high axial depth. Use coated carbide, high-pressure coolant, and keep the chipload up to avoid work hardening. Used in aerospace, oil and gas valves, and anywhere you need 304-level corrosion resistance with much higher strength. Compare to 15-5 PH (similar but better transverse properties) and 304 (easier to machine but cannot be heat treated to anywhere near the same strength).
17-7 PH
Live pricesA semi-austenitic precipitation-hardening stainless. Unique among PH grades because it starts austenitic and can be transformed to martensite through cold work or thermal treatment before aging. This gives it excellent formability in the annealed condition followed by high strength after processing. Used for spring components, diaphragms, aircraft structural parts, and surgical instruments. Machines poorly in the hardened condition. Plan all machining before final aging. Compare to 17-4 PH (martensitic from the start, easier to work with) and 301 (also work-hardens but not precipitation-hardenable).
154CM
Live pricesCPM 154 (also 154CM) is a premium martensitic stainless with high carbon and molybdenum content. Heat treats to 58-61 HRC with excellent edge retention and corrosion resistance. This is a knife steel that also sees use in high-wear industrial applications like valve seats and pump components. Machine it annealed, then heat treat. After hardening, only grinding and EDM are practical. Compare to 440C (cheaper, slightly less corrosion resistant) and CPM S30V (better toughness, similar hardness).
201
Live pricesA budget austenitic stainless that substitutes manganese and nitrogen for nickel to cut costs. Work hardens faster than 304, so you need rigid setups, sharp tools, and consistent chipload. Don't let the tool rub or you'll glaze the surface and kill your insert. Corrosion resistance is noticeably worse than 304, especially in chloride environments, so it's limited to mild indoor applications. Mostly shows up in food service equipment, decorative trim, and automotive interior parts where the end use doesn't demand serious corrosion performance. Compare to 304 (better corrosion resistance, slightly easier to machine, but more expensive due to higher nickel content). If the part needs to hold up in any kind of harsh environment, step up to 304.
301
Live pricesAn austenitic stainless that work-hardens rapidly. Lower chromium and nickel than 304 (17/7 vs 18/8), which makes it less corrosion resistant but allows significant strengthening through cold work. Used for structural applications, springs, and anywhere you need strength from a stainless without heat treatment. Available in various tempers from annealed (soft) to full hard. The harder tempers are tough on tools. In the annealed condition it machines like a slightly worse version of 304. Mainly a sheet and strip product. Compare to 304 (better corrosion resistance, less work-hardenable) and 17-7 PH (precipitation-hardenable, even higher achievable strength).
302
Live pricesThe original 18-8 stainless, essentially 304 with a slightly higher carbon range. In modern production, there's virtually no practical difference between 302 and 304. Most distributors use the terms interchangeably. 302 allows up to 0.15% carbon versus 0.08% for 304, but most heats fall well below 0.08% anyway. Machines identically to 304. If a drawing calls out 302, you can usually supply 304 without issue. Compare to 304 (functionally identical in modern production) and 301 (lower alloy content, more work-hardenable).
303
Live pricesThe free-machining stainless. Sulfur is added to break chips into short, manageable pieces instead of the bird's-nest razor wire you get with 304. Machines at roughly 78% machinability rating versus 304's 45%. You can run it faster, drills and taps go in clean, and tool life is significantly better. The tradeoff is reduced corrosion resistance and terrible weldability due to the sulfur content. If the part needs welding, don't use 303. If it doesn't, and you're doing any significant amount of machining, there's almost no reason to use 304 instead. Screw machine shops run this all day long for fittings, shafts, bushings, and valve components. Compare to 304 (better corrosion resistance and weldability but a bear to machine) and 416 (even easier to machine but less corrosion resistant).
304
Live pricesThe most common stainless steel, period. 18% chromium, 8% nickel, good corrosion resistance, excellent weldability. The downside is it's not fun to machine. It work hardens fast, produces long stringy chips that wrap around everything, and will eat tools if you let it rub instead of cut. The key is sharp carbide, aggressive chipload, moderate speed, and flood coolant. Keep the tool cutting, not rubbing. Quality varies batch to batch. Some runs cut clean, others feel like chrome bumper. Carpenter Project 70 and similar premium melts are worth the upside if you're running volume. Used everywhere from food equipment to medical devices to architectural trim. Compare to 303 (way easier to machine but can't weld it) and 316 (better corrosion resistance, slightly gummier).
304/304L
Sourcing guideDual-certified material that meets both 304 and 304L specs. The L means low carbon (under 0.03%), which prevents sensitization during welding. In practice, most mills now produce 304 to dual-cert levels since it covers more applications. Machines the same as standard 304 with all the same headaches: work hardening, stringy chips, and the need for aggressive feeds. The only meaningful difference is weldability. If the part will be welded, especially in thick sections, the low carbon matters because it prevents chromium carbide precipitation at grain boundaries that would create corrosion-susceptible zones. If it won't be welded, there's no practical advantage over standard 304.
304L
Live pricesLow carbon version of 304 (under 0.03% C versus 0.08% for standard 304). Exists specifically for welded assemblies where post-weld corrosion resistance matters. Slightly lower strength than standard 304 due to the reduced carbon, but in most machining applications you won't notice the difference. Machines identically to 304. The same rules apply: stay ahead of the work hardening, keep chipload up, use sharp coated carbide. Most commonly specified for welded tanks, piping, and pressure vessels in food, dairy, chemical, and pharmaceutical processing. In practice, the distinction between 304 and 304L is becoming less relevant since most modern production is dual-certified anyway.
309
Live pricesHigh-chromium, high-nickel austenitic stainless (23/13) designed for high-temperature service. Maintains its strength and oxidation resistance at temperatures where 304 and 316 would fail. Used for furnace parts, heat exchangers, kiln linings, and thermal processing equipment. Machines similarly to 304 but slightly tougher due to the higher alloy content. Not commonly used for ambient-temperature applications where 304 or 316 would be cheaper and perfectly adequate. Compare to 310 (even higher temperature capability) and 304 (adequate below 800°F, much cheaper).
310
Live pricesThe high-temperature stainless (25% chromium, 20% nickel). Maintains structural integrity and oxidation resistance up to 2000°F. This is the furnace fixture, radiant tube, and heat treatment basket alloy. The high nickel and chromium content makes it expensive. Machines like a tougher version of 304, with more work-hardening and gummier chips from the higher alloy content. Use sharp carbide, aggressive feeds, and flood coolant. Not commonly seen in general machining work. If it shows up, it's for a high-temperature application. Compare to 309 (slightly lower temperature rating, cheaper) and Inconel 600 (higher temperature capability, significantly more expensive).
316
Live prices304 with 2-3% molybdenum added for better pitting and crevice corrosion resistance, especially against chlorides. This is the step-up from 304 when you need to handle saltwater, chemicals, or pharmaceutical environments. Machines similar to 304 but tends to be slightly gummier and produce stringier chips due to the molybdenum. Machinability rating is around 40% versus 304's 45%. The moly makes it tougher and more prone to built-up edge on the tool. Same approach as 304: sharp tools, high chipload, flood coolant, don't let it rub. Costs more than 304 (the moly premium). Used in marine hardware, chemical processing, pharmaceutical equipment, and medical implants. Compare to 304 (cheaper, adequate if chlorides aren't a concern).
316/316L
Sourcing guideDual-certified to meet both 316 and 316L specifications. Same relationship as 304/304L: the L version has lower carbon (under 0.03%) for better post-weld corrosion resistance. Most modern production runs dual-cert because it's easier for mills to sell to a broader market. Machines the same as standard 316, which means gummier and more demanding than 304. If you're buying 316 today, there's a good chance it already meets 316L carbon limits. The distinction matters primarily on paper for welded assemblies in corrosive service where specs call out the L grade specifically. Common in chemical plant piping, marine fittings, and pharmaceutical vessels where welding and chloride exposure both come into play.
316L
Live pricesLow carbon version of 316, purpose-built for welded fabrications in aggressive corrosive environments. The low carbon prevents chromium carbide precipitation during welding, maintaining corrosion resistance in the heat-affected zone. Slightly lower tensile and yield strength than standard 316, but the difference is minimal. Machines identically to 316 with the same challenges: gummy cutting, stringy chips, and high tool wear. Machinability around 40%. The material of choice when the spec says 316 and the fabrication involves welding, especially for chemical processing, offshore, and pharmaceutical applications. If you don't need to weld it, standard 316 (or dual-cert) works fine.
316Ti
Sourcing guideTitanium-stabilized molybdenum stainless (UNS S31635). Adds a small titanium addition to 316 chemistry so heavy welded sections can operate in the 800 – 1500°F carbide-precipitation window without intergranular sensitization. Common on European chemical prints; for ambient welded work, dual-certified 316/316L is more widely carried in US warehouses.
317
Live pricesEssentially 316 with more molybdenum (3-4% vs 2-3%). The extra moly provides better pitting and crevice corrosion resistance in aggressive chemical environments, particularly those involving sulfuric acid, acetic acid, and chloride-bearing solutions. Machines slightly worse than 316 due to the additional moly. Used in chemical processing, pulp and paper, and pharmaceutical applications where 316 isn't quite corrosion resistant enough. More expensive and harder to source. Compare to 316 (adequate for most chloride environments, cheaper) and 2205 duplex (higher strength, better SCC resistance).
321
Live pricesTitanium-stabilized austenitic stainless. Same base composition as 304 but with titanium added to prevent chromium carbide precipitation during welding and high-temperature service (800-1500°F). This eliminates intergranular corrosion in the heat-affected zone without requiring the low carbon content of 304L. Used for welded structures that operate at elevated temperatures: exhaust manifolds, expansion joints, and chemical processing equipment. Machines like 304 with the same work-hardening and chip control issues. Compare to 304L (low carbon approach to the same problem) and 347 (niobium-stabilized, same concept with a different stabilizing element).
347
Live pricesNiobium (columbium)-stabilized austenitic stainless. Same concept as 321 but uses niobium instead of titanium to prevent intergranular corrosion during welding and high-temperature service. Preferred over 321 for applications above 1000°F because niobium carbides are more stable than titanium carbides at extreme temperatures. Used in jet engine components, chemical processing equipment, and high-temperature piping. Machines like 304 with similar challenges. Compare to 321 (titanium-stabilized, better below 1000°F) and 304L (low-carbon approach, simpler but not rated for continuous high-temperature service).
409
Live pricesA ferritic stainless with only about 11% chromium, stabilized with titanium. This is the exhaust system stainless. It handles high temperatures and thermal cycling well at a fraction of the cost of austenitic grades. It will rust on the surface in humid conditions, but it won't fail structurally. Machines easier than any austenitic stainless since ferritic grades don't work harden the same way. No nickel means the chips break better and the cutting forces are lower. Not commonly seen in machine shop work since most 409 applications are formed and welded, not machined. Compare to 430 (more chromium, better general corrosion resistance, takes a nicer finish) and 304 (far better corrosion resistance but significantly more expensive).
410
Live pricesThe basic martensitic stainless. 12% chromium with enough carbon to harden by heat treatment. In the annealed condition it machines reasonably well and significantly easier than 304 since it doesn't work-harden as aggressively. Can be hardened to HRC 40+ for wear resistance. Used for valve components, pump shafts, bushings, cutlery, and turbine blades. The corrosion resistance is modest, adequate for mild environments but not chemical or marine service. Magnetic in all conditions. Welds with preheat and post-weld stress relief. Compare to 416 (sulfur added for better machinability) and 420 (more carbon, higher hardness).
416
Live pricesThe best-machining stainless steel. This is a martensitic grade with sulfur added for free machining. Rated at 100% on the stainless machinability scale (the benchmark). Cuts like butter with sharp tools, chips break clean, and tool life is excellent. HSS works fine on it, though carbide obviously lasts longer. The tradeoff is corrosion resistance. It will rust, and 'stainless' is generous. Passivation helps but it's not a substitute for a more corrosion-resistant grade. Also cannot be welded due to the sulfur content. Typically used for motor shafts, gears, valves, fasteners, and any high-volume screw machine work where the part just needs basic corrosion resistance. Compare to 303 (better corrosion resistance, slightly harder to machine) and 304 (much better corrosion resistance but dramatically worse machinability).
420
Live pricesA higher-carbon version of 410 (0.30-0.40% C vs 0.15% max for 410). Heat treats to HRC 50-55, making it the standard for plastic injection mold cavities, surgical instruments, and cutlery. In the annealed condition it machines well for a stainless, significantly better than 304. After hardening, plan on grinding or EDM for final dimensions. Corrosion resistance is fair when hardened and polished but degrades if the surface is rough or the part isn't passivated. Compare to 410 (lower hardness, better corrosion resistance) and 440C (even higher hardness, more carbon, slightly better corrosion resistance).
430
Live pricesA ferritic stainless with 16-18% chromium. Takes a nice shiny finish, which is why it shows up in appliances, kitchen equipment, and decorative trim. Magnetic, unlike 304. Machines better than austenitic grades since it doesn't work harden as aggressively. Think of it as somewhere between carbon steel and 304 in terms of cutting difficulty. Chips are shorter and more manageable than what you get from 304 or 316. Not as corrosion resistant as 304 since there's no nickel, so it's limited to mild environments. Can't handle chlorides or marine exposure. Weldability is fair with proper technique. Compare to 304 (better corrosion resistance but harder to machine and more expensive) and 409 (cheaper, worse corrosion resistance, used mostly for exhaust systems).
431
Live pricesHigh-chromium, nickel-bearing martensitic stainless (UNS S43100; 16% Cr, 2% Ni). Combines the best corrosion resistance of the 400-series martensitics with high impact toughness when heat-treated to HRC 38 – 44 (180 – 200 KSI tensile). Standard for marine propeller shafts, aircraft bolts, and pump shafts.
440A
Sourcing guideHigh-carbon martensitic stainless (0.65% C, 17% Cr), the lowest-carbon member of the 440A/440B/440C family. Hardens to HRC 55 – 58 with noticeably better toughness and stain resistance than 440C, at a slight tradeoff in peak edge wear. Used for surgical blades, dental instruments, and corrosion-resistant wear strips.
440C
Live pricesThe hardest of the standard stainless steels. High carbon (0.95-1.20%) means it can heat treat to 58-60 HRC, which puts it in the same hardness range as tool steels. In the annealed state it machines reasonably well, similar to other 400 series alloys. After heat treatment it's extremely difficult to cut. Plan to do all your machining annealed and grind to final dimensions after hardening. Machinability rating is around 40% in annealed condition. Use TiAlN coated carbide and keep tools sharp. The high hardness means excellent wear resistance, so it's used for bearings, valve components, knife blades, nozzles, and injection mold inserts. Corrosion resistance is moderate, better after hardening and polishing. Compare to 416 (much easier to machine but nowhere near the hardness) and D2 tool steel (similar hardness but 440C has better corrosion resistance).
455
Live pricesCustom 455 (UNS S45500) is a precipitation-hardening martensitic stainless developed by Carpenter Technology. Ages to very high strength (220+ KSI tensile) with good corrosion resistance. Offers better stress corrosion cracking resistance than 17-4 PH. Machine in the annealed condition, then age-harden. Used in aerospace fasteners, ordnance components, and high-strength marine applications. Limited availability compared to 17-4. Compare to 17-4 PH (more common, lower strength) and 13-8 Mo (comparable strength, different corrosion profile).
465
Sourcing guideCustom 465 (UNS S46500) is a premium precipitation-hardening martensitic stainless from Carpenter. Achieves ultimate tensile strengths exceeding 250 KSI with excellent toughness and corrosion resistance comparable to 304. One of the strongest stainless steels available. Machine in the annealed condition. After aging it requires carbide or CBN tooling. Used for critical aerospace components, military ordnance, and extreme-performance fasteners. Very expensive and limited availability. Compare to 13-8 Mo (lower strength, more available) and PH 13-8 Mo (the closest competitor in performance).
2205
Live pricesDuplex stainless steel (22% chromium, 5% nickel, 3% molybdenum). A 50/50 mix of austenite and ferrite phases that gives roughly twice the yield strength of 304 or 316 with superior chloride stress corrosion cracking resistance. Used in chemical processing, oil and gas, pulp and paper, and marine applications where standard austenitics fail. Machines harder than 316 due to the higher strength and duplex microstructure. Needs rigid setups, sharp coated carbide, and 30-40% slower speeds than 316. Chips are tough and stringy. Compare to 316 (easier to machine, adequate for less aggressive environments) and 2507 super duplex (even stronger, even harder to machine).
2507
Sourcing guideSuper duplex stainless steel (UNS S32750; 25% Cr, 7% Ni, 4% Mo, 0.27% N). Steps above 2205 duplex with 80+ KSI yield strength and PREN > 40 pitting resistance for warm seawater, subsea umbilicals, desalination, and brine pumps. Expect high cutting forces and rapid work-hardening; run rigid setups, low SFM, and high-pressure coolant.
AEB-L
Live pricesA Swedish martensitic stainless steel optimized for razor-thin edges. Very fine carbide structure from the controlled composition (0.67% C, 13% Cr) produces exceptional edge quality when properly heat treated. The knifemaking community's favorite stainless blade steel for thin, precision-ground edges. Heat treats to HRC 60-62. Machine annealed, then heat treat. Compare to 440C (coarser carbides, slightly higher hardness) and 154CM (higher alloy content, better edge retention).
Alloy 20
Sourcing guideNickel-iron-chromium austenitic alloy (UNS N08020 / Carpenter 20Cb-3; ~34% Ni, 20% Cr, 3.5% Cu, 2.5% Mo) engineered specifically for hot sulfuric acid, pickling tanks, and mixed chemical process piping. Sits between 316L stainless and higher-priced Incoloy 825 or Hastelloy C-276, and machines like a tough, gummy austenitic stainless.
Greek Ascoloy
Live pricesA martensitic stainless steel (UNS S41800) with tungsten and vanadium additions for high-temperature strength and creep resistance. Designed for gas turbine and jet engine components operating at moderate to high temperatures. Can be hardened to HRC 35-40. Machines reasonably well in the annealed condition. Rarely seen outside of aerospace and power generation applications. Compare to 410 (simpler chemistry, no high-temperature benefit) and Inconel 718 (much higher temperature capability but far more expensive).
Nitronic 50
Live pricesA nitrogen-strengthened austenitic stainless (UNS S20910) with roughly twice the yield strength of 316 in the annealed condition. Excellent corrosion resistance, comparable to 316, combined with high strength without cold working. Non-magnetic. Used for marine fasteners, valve stems, pump shafts, and any application needing the corrosion resistance of 316 with significantly more strength. Machines harder than 316 due to the higher strength. Use carbide, reduce speeds, and keep feeds aggressive. Compare to 316 (half the yield strength, easier to machine) and 2205 duplex (similar strength, magnetic, different corrosion profile).
Nitronic 60
Live pricesA nitrogen-strengthened austenitic stainless (UNS S21800) with exceptional galling resistance. Where 304 and 316 will gall and seize under metal-to-metal sliding contact, Nitronic 60 resists it. This makes it the go-to alloy for wear rings, bushings, pins, and any component that slides against another stainless part without lubrication. Also has high strength similar to Nitronic 50. Machines slightly better than Nitronic 50. Compare to 316 (will gall under sliding contact) and Stellite (cobalt-based hardfacing, even better wear resistance but much more expensive).
PH 13-8 Mo
Sourcing guide13-8 Mo PH (precipitation-hardening martensitic stainless). One of the highest-strength stainless steels available, reaching 220+ KSI tensile after aging. Better transverse toughness than 17-4 PH and slightly better corrosion resistance. Machine it in the solution-annealed condition (Condition A) where it's manageable, then age-harden. After aging it's extremely tough on tools. Used for high-performance aerospace components, landing gear parts, and structural fasteners where 17-4 PH isn't strong enough. Expensive and harder to source than 17-4. Compare to 17-4 PH (lower strength, more available, cheaper) and 15-5 PH (better transverse properties than 17-4 but lower strength than 13-8).
US Suppliers That List Stainless Steel
Showing 5 of 109 suppliers in our directory. Filter by grade, shape, and ship-to state in Supplier Search.
How Shop Buyers Choose a Stainless Steel Grade
Quick side-by-side reference for common forms, shop applications, and purchasing pitfalls before you send out quotes.
| Grade | Typical Forms & Sizes | Best Shop Fit | What to Watch Out For |
|---|---|---|---|
| 303 (Free-Machining) | Cold-drawn & centerless-ground round, hex, and square bar (12 ft) | High-volume CNC turned fittings, nuts, shafts, and non-welded bushings | Sulfur addition ruins weldability (cracks in welds) and lowers chloride pitting resistance vs 304 |
| 304 / 304L | 2B/#4 sheet, HRAP plate, bar, ornamental & structural tube, angle, pipe | Food equipment, sanitary weldments, architectural frames, and general chemical tanks | Work-hardens fast under dull cutters; specify dual-certified 304/304L whenever parts are welded |
| 316 / 316L | Sheet, plate, cold-finished & pump-shaft bar, seamless/welded tube & pipe | Marine hardware, chloride washdown, pharmaceutical manifolds, and coastal structures | Carries a hefty molybdenum surcharge over 304; verify whether 304L suffices on indoor non-chloride parts |
| 17-4 PH | Condition A, H900, H1025, H1150 round/flat bar and aerospace plate | High-strength aerospace fittings, valve stems, pump shafts, and mold inserts | State Condition A (annealed) vs pre-aged H900/H1150 (NACE sour-service requires double-aged H1150D/H1150M) |
| 416 & 440C | Annealed or pre-hard round/hex bar (416); annealed bar & flats (440C) | Fast-machining magnetic shafts/gears (416) and HRC 58 – 60 wear bearings/knives (440C) | Modest corrosion resistance compared to 300-series; avoid saltwater or stagnant acid exposure |
| 2205 Duplex & Nitronic 60 | Plate, round bar, and process pipe (2205); round bar (Nitronic 60) | High-strength chloride pressure vessels (2205) and non-galling sliding pins/valve trim (Nitronic 60) | Roughly double the yield strength of 316; requires rigid CNC setups and slower surface speeds |
What to Specify on a Stainless Steel RFQ
Include these details on line 1 of your quote request so distributors price the same spec and surface finish.
Dual-cert 304/304L and 316/316L vs straight grade
Most North American bar and plate heats today are dual-certified (low carbon for weldability plus nitrogen to meet full straight-grade tensile strength). Requesting dual-cert prevents weld sensitization while matching standard distributor inventory.
Sheet & plate finish (2B, #4 Brushed, #8 Mirror, HRAP)
Cold-rolled stainless sheet defaults to 2B mill finish; cosmetic panels need #4 polished with PVC laser film, while plate 3/16 in and thicker defaults to dull Hot-Rolled Annealed & Pickled (HRAP).
Bar tolerance tier (CF, Centerless Ground, or Pump Shaft Quality)
Standard cold-finished bar works for chuckers, Swiss machines need centerless-ground 'CG' tolerances, and long rotating shafts need Turned, Ground & Polished (TGP / PSQ) straightness.
Improved-machining melts for production turning
On 500+ lb bar runs of 304L, 316L, or 17-4 where 303 sulfur isn't allowed, asking bar houses for calcium-treated improved-machining melts (such as Ugima, Prodec, or Project 70+) can boost insert life by 25~50%.
Frequently Asked Questions: Buying Stainless Steel
- Why do stainless steel distributor prices change on the 1st of every month?
- Domestic stainless mills (led by North American Stainless and Outokumpu) publish monthly alloy and fuel surcharges tied to trailing 30-day nickel, chromium, molybdenum, and natural gas averages. Service centers adjust replacement list and quote pricing alongside those monthly surcharge tables.
- Can I substitute 303 stainless for 304 to cut CNC cycle time?
- Only if the customer approves in writing AND the part is never welded, brazed, or exposed to aggressive chlorides or acids. Never substitute 303 silently for 304 on a print.
- What is the difference between ornamental stainless tube (ASTM A554) and sanitary/pressure tube (A269 / A270)?
- ASTM A554 is welded mechanical/architectural square, rectangular, and round tubing with an internal weld bead and no pressure test. Fluid lines need ASTM A269/A213 pressure tubing, and food/pharma lines need ASTM A270 ID-polished sanitary tubing.
Already have a supplier quote in hand? Check if the price is fair.