Brass Suppliers & Grades

Free-machining C360, lead-free C365, cartridge 260, forging C377, naval 464, and architectural C385 brass bar, rod, sheet, and tube.

Brass pricing tracks copper and zinc exchange moves, while shop economics turn on two questions: leaded screw-machine speed vs potable-water lead-free compliance, and whether your distributor credits clean C360 turnings on high-volume bar accounts.

Brass Grades & Trade Names

230 Red Brass

Live prices

Red brass (85% copper, 15% zinc). Richer in copper than yellow brasses, giving it better corrosion resistance and a warm reddish-gold color. Machines reasonably well but not in the same league as C360. Used for architectural hardware, plumbing fittings, and decorative applications where the color matters. Good for brazing and soldering. The higher copper content makes it noticeably more expensive than common yellow brass. Compare to 260 cartridge brass (cheaper, more yellow, less corrosion resistant) and C110 copper (even more corrosion resistant but much harder to machine).

260 Cartridge Brass

Live prices

Cartridge brass (70% copper, 30% zinc). Named for its original use in ammunition cartridge cases. Excellent cold formability - it deep-draws beautifully. Not a machining alloy. In the shop, it's soft, gummy, and produces long stringy chips. Its strength is in forming: stamped parts, drawn shells, radiator cores, and decorative hardware. Available mainly in sheet, strip, and wire. If someone specs 260 for a machined part, ask why - C360 machines dramatically better. Compare to C360 (far better machinability) and 230 red brass (higher copper, warmer color, better corrosion resistance).

272

Live prices

Yellow brass (63% copper, 37% zinc). Near the maximum zinc content for single-phase alpha brass. Good balance of strength and formability, slightly cheaper than 260 due to higher zinc content. Used for architectural trim, engraving plates, and general decorative applications. Machinability is mediocre - better than pure copper, worse than leaded brasses. Compare to 260 (more copper, better formability) and C360 (leaded, dramatically better machinability).

280 Muntz Metal

Live prices

Muntz metal (60% copper, 40% zinc). A duplex alpha-beta brass that's strong, hard, and corrosion resistant in marine environments. The high zinc content makes it one of the cheapest brasses. Machines reasonably in the beta phase but isn't free-cutting. Used for architectural panels, condenser tubes, and large hot-forged parts. Compare to 464 naval brass (tin added for better seawater resistance) and C360 (leaded for free-machining).

314

Live prices

Leaded commercial bronze (89% copper, 9.25% zinc, 1.75% lead). Despite the "bronze" name, this is technically a low-zinc brass with lead added for machinability. The high copper content gives excellent corrosion resistance and a rich bronze color. Machines well thanks to the lead. Used for screws, rivets, hardware, and decorative components where corrosion resistance and appearance matter. Compare to C360 (better machinability, more yellow) and 230 red brass (similar color, no lead).

335

Live prices

Low-leaded brass (65% copper, 34.5% zinc, 0.5% lead). Just enough lead to improve machinability slightly over unleaded yellow brass without the higher lead content of C360. A compromise alloy for applications where some machinability improvement is needed but lead content must be minimized. Used for hardware, fittings, and decorative parts. Compare to C360 (much better machinability, higher lead) and 260 (no lead, worse machinability).

353 High-Leaded Brass

Live prices

High-leaded brass (62% copper, 36% zinc, 2% lead). A clock and instrument brass with excellent machinability thanks to the generous lead content. Very close to C360 in cutting performance. Used for clock components, instrument parts, engraving stock, and precision small parts. Not as widely stocked as C360 but machines just as well. Compare to C360 (more common, slightly different composition) and C385 (architectural bronze, similar lead content).

464 Naval Brass

Live prices

Naval brass (60% copper, 39.25% zinc, 0.75% tin). The tin addition significantly improves dezincification resistance in seawater compared to standard yellow brass. This is propeller shaft material, marine hardware material, and turnbuckle material. Machines adequately but not great - no lead, so chips are long and stringy. Used wherever brass needs to survive salt water long-term. Compare to 280 (cheaper, no tin, less seawater resistant) and C360 (much better machinability but not rated for marine immersion).

485 Leaded Naval Brass

Live prices

Leaded naval brass (60% copper, 37.5% zinc, 1.75% lead, 0.75% tin). Combines the seawater corrosion resistance of C464 naval brass with the machinability benefits of lead. The best-machining marine brass. Used for marine hardware, fittings, and valve components that need to be both machined and seawater-resistant. Compare to 464 (unleaded version, worse machinability) and C360 (better machinability but no marine corrosion resistance).

693

Live prices

Silicon red brass (81.5% copper, 14.5% zinc, 4% silicon). An uncommon specialty alloy with high strength and excellent corrosion resistance. The silicon addition improves wear resistance and gives it self-lubricating properties in bearing applications. Harder to machine than leaded brasses but manageable with carbide. Used for bearings, gears, and marine hardware where strength and corrosion resistance are both critical. Compare to 655 silicon bronze (higher copper, no zinc) and 464 naval brass (different approach to marine corrosion).

C360

Live prices

The gold standard for machinability. Literally. C360 is rated at 100% on the machinability scale - it's the benchmark everything else is measured against. The lead content (2.5 – 3.7%) is what makes it work, producing short, broken chips at high speeds with minimal tool wear. You can run it fast, feed it hard, and your inserts will last forever compared to steel. Screw machine shops live on this stuff. Fittings, valves, sensor bodies, gears, and anything that comes off an automatic lathe in high volume. Coolant is optional - some shops run it dry to avoid staining the brass. Compared to 12L14 steel (its main competitor for screw machine work), C360 is actually cheaper per finished part despite higher material cost because cycle times are dramatically lower. Not weldable, and the lead content means it's not food/water safe under current regulations.

C365

Sourcing guide

Lead-free free-machining brass with bismuth replacing lead. Designed as a drop-in replacement for C360 in plumbing and potable water applications after lead regulations tightened. Bismuth provides chip-breaking similar to lead but without the toxicity. Machinability is close to C360 but not quite as good - most machinists report about 80 – 85% of the performance. Required for any NSF/ANSI 61 potable water application. Compare to C360 (better machinability but contains lead) and 260 (no lead or bismuth, poor machinability).

C377 Forging Brass

Sourcing guide

Forging brass (UNS C37700 / CDA 377; 59% copper, 39% zinc, 2% lead). The industry-standard hot-forging brass because its beta-phase plasticity at forging temperatures fills complex valve and fitting dies cleanly, while the 2% lead gives ~80% machinability for secondary turning and threading.

C385 Architectural Bronze

Live prices

Architectural bronze (actually a leaded brass: 57% copper, 40% zinc, 3% lead). Don't let the name fool you - this is a brass, not a true tin bronze. The lead gives it free-machining properties similar to C360. Its selling point is the warm, dark gold color and excellent weathering characteristics for exterior applications. Storefronts, door handles, window frames, and decorative panels are its sweet spot. Machines well and extrudes well. Compare to C360 (similar machinability, lighter color) and 280 Muntz metal (cheaper, no lead, harder to machine).

US Suppliers That List Brass

Showing 5 of 23 suppliers in our directory. Filter by grade, shape, and ship-to state in Supplier Search.

Filter by state (23 total)

How Shop Buyers Choose a Brass Alloy

Quick side-by-side reference for common forms, shop applications, and purchasing pitfalls before you send out quotes.

GradeTypical Forms & SizesBest Shop FitWhat to Watch Out For
C360 (Free-Machining)12 ft round, hex, square, and rectangular bar (H02 half-hard)High-speed Swiss and screw-machine fittings, pneumatic valves, gears, and insertsContains ~3% lead; prohibited in US potable drinking-water wetted parts and strict RoHS exemptions
C365 / Lead-Free BrassRound and hex rod, forging stockNSF/ANSI 61 & Safe Drinking Water Act (<0.25% Pb) plumbing valves, meters, and stemsCosts more per pound than C360 and requires segregated chip bins so leaded chips don't downgrade scrap value
260 (Cartridge Brass)Sheet, coil, shim strip, tube, and wireStamped terminals, deep-drawn shells, instrument panels, and formed bracketsUnleaded and gummy on a lathe; never order 260 bar for turned fittings when C360 works
464 & 485 Naval BrassRound bar, marine shafting, hex bar, and condenser plateSaltwater propeller shafts, turnbuckles, thru-hulls (464), and machined marine valves (485)Unleaded 464 strings chips; specify leaded 485 naval brass if heavy turning/threading is required
C385 (Architectural Bronze)Extruded angle, channel, threshold shapes, flat bar, and square barSharp-corner architectural trim, door hardware, handrails, and decorative millworkMetallurgically a leaded brass (57 Cu / 40 Zn / 3 Pb), not a tin bearing bronze

What to Specify on a Brass RFQ

Include these details on line 1 of your quote request so distributors price the same spec and surface finish.

Potable-water / RoHS lead restrictions

US drinking-water fittings require <=0.25% weighted-average lead (NSF/ANSI 61 / 372, such as bismuth-bearing C89835/EnviroBrass, silicon brass C693/Eco Brass, or C27450), while EU RoHS 6(c) caps lead in copper alloys (historically 4%, subject to sunset reviews). Verify regulatory callouts before ordering C360.

Temper on rod and sheet (H02 Half-Hard vs Annealed)

C360 machining rod defaults to H02 (half-hard) per ASTM B16 for crisp chip breaking; 260 sheet defaults to H02 half-hard for flat panels/moderate bends or O60 soft-annealed for deep drawing.

Swiss straightness and chamfered bar ends

In 12 ft bar feeders, standard ASTM B16 rod can whip at high RPM; request screw-machine/Swiss straightness and pointed/chamfered bar ends on production orders.

Clean C360 turnings buyback

Screw-machine jobs often turn 40~65% of brass bar weight into chips. Brass mills and non-ferrous distributors pay top scrap value only when C360 chips are kept 100% separate from steel, aluminum, and bismuth/silicon lead-free brass.

Frequently Asked Questions: Buying Brass

Why is C360 brass sometimes cheaper per finished part than 12L14 steel despite costing 3 – 4x more per pound?
C360 runs at 300 – 1,000+ SFM with tiny cycle times, multi-day insert life, no rust-preventative oiling, and high clean-turnings scrap recovery, often beating steel once spindle minutes and secondary plating are counted.
Why is C385 called 'Architectural Bronze' when it's listed under Brass?
Trade convention in architectural metalwork names C38500 'architectural bronze' for its warm golden-brown patina, even though its 57% copper, 40% zinc, 3% lead chemistry makes it a free-machining extruded brass.
What happens if leaded C360 chips mix with Eco Brass or bismuth lead-free brass chips?
Bismuth and silicon contaminate conventional C360 brass mill remelts, causing recyclers to downgrade mixed bins sharply. Shops running both alloys keep dedicated, labeled chip drums.