Bronze Suppliers & Grades
C932 bearing bronze, C954 and C630 aluminum bronze, C510/C544 phosphor bronze, and C655 silicon bronze.
Bronze isn't one metal: bearing bronzes (C932/C954) come from continuous-cast foundry master distributors in cored tubes and 105-inch or 12-foot bars, while wrought phosphor and silicon bronzes (C510, C544, C655) flow through non-ferrous rod and strip mills.
Bronze Grades & Trade Names
907
Sourcing guideTin bronze (89% copper, 11% tin). The highest tin content in the common tin bronze series. Maximum wear resistance and hardness among the tin bronzes, making it ideal for heavy-duty gears and worm wheels. The high tin content gives excellent resistance to saltwater corrosion. Used in marine propulsion gears, heavy industrial bearings, and pump components where maximum wear life is required. Harder to machine than lower-tin alloys but manageable with carbide. Compare to C905 (slightly less tin, slightly easier to machine) and C954 aluminum bronze (different alloy system, higher strength).
C220 Commercial Bronze
Live pricesCommercial bronze (90% copper, 10% zinc). Despite the name, this is technically a brass - the industry just calls it bronze because of its rich coppery color. Very good corrosion resistance, excellent for cold forming, and takes a beautiful finish. Not a machining alloy. Used for weatherstripping, hardware, screen cloth, rivets, and decorative architectural trim. If you need to machine it, treat it like copper: sharp tools, positive rake, high speed. Compare to C230 red brass (85/15, similar applications) and C110 copper (better conductivity but harder to form).
C510 Phosphor Bronze
Live pricesPhosphor bronze A (95% copper, 5% tin, trace phosphorus). The standard phosphor bronze. Excellent spring properties, fatigue resistance, and corrosion resistance. This is the spring clip, bellows, and electrical connector alloy. Machines poorly - it's tough, work-hardens rapidly, and produces long stringy chips that wrap around everything. If you must machine it, use sharp carbide, aggressive feeds, and flood coolant. Available mainly in sheet, strip, wire, and rod. In the shop, you'll usually see it being formed, not cut. Compare to 544 (same family, free-machining version with lead) and 260 cartridge brass (easier to form but weaker spring properties).
C544 Phosphor Bronze
Live pricesFree-cutting phosphor bronze (88% copper, 4% tin, 4% lead, 4% zinc). The machinability-optimized version of the phosphor bronze family. Lead content brings the machinability rating up to around 80 - dramatically better than unleaded C510. Used for screw machine parts that need the corrosion resistance and wear characteristics of phosphor bronze with reasonable machinability. Gears, bushings, bearings, and precision turned components. Compare to C510 (much harder to machine but better spring properties) and C932 (higher lead content, designed specifically for bearing applications).
C614 Aluminum Bronze
Sourcing guideAluminum bronze (91% copper, 7% aluminum, 2% iron). High strength, excellent corrosion resistance, and outstanding wear resistance. Significantly stronger than tin bronzes or leaded bronzes. Used for heavy-duty bearings, valve guides, bushings under high loads, and marine hardware. Machines harder than leaded bronzes but manageable with carbide tooling - think of it as similar difficulty to 4140 steel. The aluminum content creates a tough, work-hardening surface. Rigid setups and aggressive feeds are key. Compare to C954 (even higher aluminum content, stronger) and C932 (softer, easier to machine, lower load capacity).
C623 Aluminum Bronze
Sourcing guideAluminum bronze (UNS C62300 / CDA 623; 87% copper, 10% aluminum, 3% iron). High-strength wrought rod and bar grade used for valve stems, worm gears, cams, and heavy wear guides. Machines like medium-carbon steel; keep carbide sharp and never let the tool rub.
C630 Nickel Aluminum Bronze
Live pricesNickel aluminum bronze (81% copper, 10% aluminum, 5% nickel, 4% iron). One of the highest-strength copper alloys available. Exceptional corrosion resistance in seawater and excellent resistance to cavitation erosion. This is ship propeller material, pump impeller material, and heavy-duty valve seat material. Strength approaches medium-carbon steel levels. Machines like a tough alloy steel - needs rigid setups, sharp carbide, moderate speeds, and aggressive feeds. Do not let the tool rub. Used in marine, oil and gas, and power generation applications. Compare to C954 (slightly lower strength, more common) and 614 (lower aluminum, lower strength, easier to machine).
C642 Silicon Aluminum Bronze
Live pricesAluminum silicon bronze (91.5% copper, 7% aluminum, 1.5% silicon). The silicon addition improves castability and adds slightly better wear properties compared to straight aluminum bronze. Good corrosion resistance and high strength. Used for pump components, valve bodies, marine hardware, and wear-resistant bushings. Machines similarly to 614 - tough but manageable with carbide. Compare to 614 (no silicon, slightly different properties) and 655 silicon bronze (different alloy system, more silicon, less aluminum).
C655 Silicon Bronze
Live pricesSilicon bronze (97% copper, 3% silicon). High strength with excellent corrosion resistance, especially in industrial and marine atmospheres. The go-to alloy for welded bronze fabrications because it welds beautifully with standard TIG/MIG processes. Used for marine hardware, poles, chemical equipment, and anywhere you need a strong, weldable, corrosion-resistant copper alloy. Machines harder than leaded bronzes - the silicon makes it tough and somewhat gummy. Use sharp carbide at moderate speeds. Compare to 614 aluminum bronze (even stronger, different corrosion profile) and C510 phosphor bronze (better spring properties, worse machinability).
C673 Manganese Bronze
Live pricesManganese bronze (58.5% copper, 39% zinc, 1.4% iron, 1% tin, 0.1% manganese). Despite the name, this is essentially a high-strength brass with minor additions. Very high tensile strength for a copper alloy (65 – 80 KSI). Used for heavy-duty gears, large propeller shafts, valve stems, and structural marine applications. Machines adequately - better than silicon bronze, worse than leaded brass. The iron content gives it wear resistance beyond what plain brass offers. Compare to 464 naval brass (lower strength, better dezincification resistance) and 630 nickel aluminum bronze (higher strength, better corrosion resistance, harder to machine).
C836 Leaded Red Brass
Sourcing guideLeaded red brass / ounce metal (UNS C83600 / SAE 40; 85% copper, 5% tin, 5% lead, 5% zinc). The classic '85-5-5-5' cast valve, pump body, and low-pressure plumbing bronze. Machines cleanly (~84% machinability) with pressure-tight casting behavior and reliable water corrosion resistance.
C903 Tin Bronze
Sourcing guideTin bronze (88% copper, 8% tin, 4% zinc). An excellent general-purpose bearing and gear bronze with good corrosion resistance and moderate strength. Higher tin content than C932 gives better wear resistance under moderate loads. Used for pump impellers, piston rings, valve components, steam fittings, and gears operating in corrosive environments. Machines well with standard tooling. Compare to C932 (higher lead, better machinability, lower strength) and C905 (more tin, even better wear resistance).
C905 High-Tin Bronze
Sourcing guideHigh-tin bronze (88% copper, 10% tin, 2% zinc). The higher tin content compared to C903 provides improved wear resistance and hardness. Excellent for gears, bearings, and bushings under heavy loads in corrosive environments. This is the premium tin bronze for demanding applications. Machines adequately - harder than leaded bronzes but not as difficult as aluminum bronzes. Used in marine applications, pumps, and heavy machinery. Compare to C903 (slightly less tin, more zinc, similar applications) and C954 aluminum bronze (higher strength, different wear characteristics).
C932 Bearing Bronze
Live pricesThe default bearing and bushing bronze. If someone says "bearing bronze" without specifying an alloy, they mean C932. It's a high-lead tin bronze (83% copper, 7% tin, 7% lead, 3% zinc) designed for anti-friction applications under medium loads and speeds with lubrication. Machines well with a machinability rating around 70 - the lead content helps with chip breaking, similar to how it works in C360 brass. Used for bushings, thrust washers, pump impellers, wear strips, and light-duty gears everywhere from construction equipment to machine tools. The lead acts as a built-in lubricant at the bearing surface, which is the whole point. If you need higher load capacity, step up to C954 aluminum bronze. If you need better corrosion resistance in marine environments, C932 is still adequate but not ideal. Most shops machine it without issues using standard tooling.
C937
Live pricesHigh-leaded tin bronze (80% copper, 8% tin, 10% lead, 2% zinc). Even more lead than C932, making it the best-machining bronze alloy. Designed for bearings and bushings under lighter loads where easy machinability and excellent anti-friction properties are the priority. The extra lead provides superior self-lubricating behavior. Used for general-purpose bearings, thrust washers, and backing plates. Compare to C932 (less lead, slightly stronger, the more common bearing bronze) and 544 (free-cutting phosphor bronze, better spring properties).
C954 Aluminum Bronze
Live pricesAluminum bronze (85% copper, 11% aluminum, 4% iron). The workhorse heavy-duty bearing bronze. Significantly stronger and harder than tin bronzes or leaded bronzes - tensile strength can exceed 90 KSI. Excellent wear resistance, corrosion resistance, and impact toughness. Used for heavy-duty bearings in steel mills, landing gear bushings, bridge trunnions, and marine propeller hubs. Machines like a tough steel - rigid setups, carbide tooling, and aggressive feeds are mandatory. Don't try HSS. Compare to C932 (much easier to machine but far less strong) and 630 nickel aluminum bronze (even stronger, even harder to machine).
C955 Nickel Aluminum Bronze
Live pricesCast nickel-aluminum bronze (UNS C95500; 81% copper, 11% aluminum, 4% nickel, 4% iron). Cast counterpart to wrought C63000 with 90 – 110+ KSI tensile strength and strong resistance to seawater, cavitation, and heavy bearing loads. Used for marine hardware, landing-gear bushings, and heavy worm gears.
C959 High-Aluminum Bronze
Sourcing guideHigh-aluminum cast bronze (UNS C95900; ~12 – 13% aluminum, 4% iron). Extra aluminum raises hardness (Brinell 240+) and compressive strength for deep-drawing dies, forming rolls, and non-galling wear plates against stainless steel, at the cost of lower ductility and tougher carbide machining.
C89835
Live pricesA bismuth-tin bronze designed as a lead-free replacement for traditional leaded bearing bronzes like C932. The bismuth provides similar machinability and anti-friction properties to lead without the toxicity. Required for potable water applications and increasingly specified for environmental compliance. Machines comparably to C932. Used for lead-free bushings, valve bodies, and plumbing fittings. Compare to C932 (traditional leaded version, slightly better machinability) and C365 lead-free brass (different alloy system for lead-free requirements).
SAE 841
Live pricesOil-impregnated sintered iron-bronze bearing (iron-based with copper and tin). Higher load capacity and wear resistance than pure sintered bronze (SAE 863). The iron base gives structural strength while the bronze and oil provide lubrication. Self-lubricating under normal operating conditions. The standard for medium-duty sleeve bearings in automotive, agricultural, and industrial equipment. Not a machining material - pressed to net shape from powder. Compare to SAE 863 (pure bronze, lower load capacity, better corrosion resistance) and C932 (cast bronze, much higher load capacity, fully machinable).
SAE 863 / C863 Bronze
Live pricesSintered bronze, oil-impregnated (SAE 863 specification). Made by compacting bronze powder and sintering it into a porous structure, then vacuum-impregnating with oil. The porosity acts as an oil reservoir - the bearing self-lubricates under load. This is the standard for small, low-speed bearings in motors, appliances, power tools, and office equipment. Not a machining material. Bushings are pressed to net shape from powder and rarely see secondary machining. If they do, use light cuts at low speed to avoid collapsing the porous structure. Compare to C932 (cast bearing bronze, higher load capacity) and SAE 841 (iron-based sintered bearing, higher strength).
US Suppliers That List Bronze
Showing 5 of 18 suppliers in our directory. Filter by grade, shape, and ship-to state in Supplier Search.
How Shop Buyers Choose a Bronze Alloy
Quick side-by-side reference for common forms, shop applications, and purchasing pitfalls before you send out quotes.
| Grade | Typical Forms & Sizes | Best Shop Fit | What to Watch Out For |
|---|---|---|---|
| C932 (SAE 660 Bearing) | Continuous-cast solid rounds, cored hollow bar (105 in / 144 in), and wear flats | General lubricated sleeve bushings, thrust washers, spindle bearings, and wear strips | Contains 7% lead (not potable-water compliant; use C89835 instead) and deforms under extreme shock loads |
| C954 (Aluminum Bronze) | Continuous-cast solid & cored bar, wear plate, and centrifugally cast rings | Heavy-load mill bearings, landing-gear bushings, forming-die wipes, and worm gears | 85+ KSI tensile and work-hardening skin; machines like tough alloy steel (carbide required, never rub) |
| C630 & C955 (Nickel Aluminum Bronze) | Wrought AMS 4640 / ASTM B150 bar (C630) and cast hollow/solid stock (C955) | Subsea valve stems, ship propeller hubs, aircraft bushings, and seawater pump parts | Verify wrought C63000 vs cast C95500 on aerospace and Navy MIL-B-24480 / AMS prints |
| C510 & C544 Phosphor Bronze | Spring strip/sheet & rod (C510); free-cutting screw-machine rod (C544) | Electrical spring contacts & bellows (C510) and turned pinions, valve spindles & bearings (C544) | Unleaded C510 wraps razor-sharp stringy chips on lathes; always check if leaded C544 (B139) is allowed for turned parts |
| C655 (Silicon Bronze) | Rod, plate, sheet, hex bar, and TIG weld filler | TIG-welded marine hardware, architectural fabrications, shafting, and chemical bolts | Chosen for strength + weldability rather than low-friction sleeve-bearing duty |
What to Specify on a Bronze RFQ
Include these details on line 1 of your quote request so distributors price the same spec and surface finish.
Cored (hollow) bar vs solid bar on bushings
Continuous-cast C932 and C954 are cast in hundreds of OD x ID cored combinations with built-in cleanup allowance (typically +1/32 in on OD and -1/32 in on ID under 3 in, +1/16 in from 3 – 5 in). Buying cored tube instead of drilling out solid bronze often cuts material cost by 35~55%.
Continuous-cast (ASTM B505) vs sand-cast (B584) or centrifugal (B271)
ASTM B505 continuous-cast bar eliminates sand inclusions and delivers finer, denser bearing grain than B584 sand castings. Large diameters above ~12 – 16 inches normally transition to ASTM B271 centrifugally cast rings.
Standard 105-inch (8 ft 9 in) foundry bar lengths
Many continuous-cast bearing bronzes are cast and sold in traditional 105 in (or 144 in) lengths rather than 12 ft steel lengths; plan saw kerfs and part nesting around 105 in so you don't come up two bushings short.
Lead-free potable water or RoHS callouts
Standard C932 (7% Pb) and C544 (4% Pb) fail NSF-61 drinking-water rules; request C89835 bismuth tin bronze or C954 aluminum bronze when lead-free certification is required.
Frequently Asked Questions: Buying Bronze
- How much cleanup allowance is built into continuous-cast C932 and C954 bronze bar?
- Nominal cast bronze sizes already include machining stock so a '2 in OD x 1 in ID' cored bar finishes cleanly to a 2.000 in OD and 1.000 in ID bushing (typically ~1/32 in oversize on OD and ~1/32 in undersize on ID up to 3 in OD, and 1/16 in on 3 – 5 in OD). Check the producer's finish-allowance chart before sizing up.
- When should an engineer step up from C932 bearing bronze to C954 aluminum bronze?
- C932 excels at higher surface speeds with boundary grease/oil lubrication and mild shaft hardness, because embedded lead prevents shaft scoring. C954 handles heavy shock loads, slow oscillating pivots, and abrasive grit, but requires a hardened mating shaft (typically HRC 45+) and reliable lubrication.
- What is SAE 841 / SAE 863 'Oilite' bronze compared to C932?
- Oilite (SAE 841/863) is powder-metallurgy porous bronze vacuum-impregnated with ~18~20% oil by volume for light, ungreased sleeve bearings. Standard cutting tools smear the pores shut if bored improperly; use razor-sharp single-point carbide or diamond tools with no coolant.
Already have a supplier quote in hand? Check if the price is fair.